Cooper Security i-on 16 Guia de Instalação descarregar pdf (Página 11)

i-on40

Page 7

control unit and 5 in Fig 8 for the keypad).

Fitting a jumper to the pins adds a

termination to the cable.

In a daisy chain configuration terminate

each end of the chain (see Fig 11 ).

In a star configuration:

If there are only two keypads then this

is the same as a daisy chain

configuration. If required terminate at

each keypad.

If there are more than two keypads

AND two cables are long while the

remaining keypad cables are short (less

than 10m) then it is possible to

terminate at the two keypads with long

cables.

If there are more than two keypads BUT

each keypad cable is more than 10m

then DO NOT terminate.

Keypad Addressing

Each keypad connected to an end station

must have a unique address. See Figure 8

on page 4 for the position of the addressing

jumpers.

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

*0#

MENU

A

B

1

4 ghi

7 pqrs

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

4

3

2

4

3

2

12

43

4

3

2

4

3

2

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

Figure 13 Keypad Addressing Jumpers

Backlight Control

You can control the appearance of the

keypad backlights and set/unset LEDs by

fitting links over the appropriate jumpers

on the keypad pcb (see Figure 8 on page 4

for the position of the jumpers).

The jumpers have the following functions:

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

ABCD-ON

The set/unset LEDs are disabled.

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

ABCD-ON

The set/unset LEDs shows the setting

status of the system. (Full set is left

hand led.)

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

ON

BRIGHT

BL

The key backlights are disabled. They

will glow briefly for five seconds when a

user presses a key.

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

ON

BRIGHT

BL

The key backlights glow all the time at

normal intensity.

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

MENU

A

B

1

4 ghi

7 pqrs

*0#

2 abc

5 jkl

3 def

6 mno

8 tuv 9 wxyz

ON

BRIGHT

BL

The keypad backlights glow all the time,

extra bright.

Tone Volume

To alter the volume of non-alarm tones

from the keypad adjust the keypad sounder

volume control (2 in Fig 8):

Louder

Note: This control changes

the volume of non-alarm

tones (for example

Exit/Entry tone). The volume

of alarm tones is fixed.

Softer

Step 3. Connect End

Station to Mains

WARNING: ENSURE THAT THE MAIN

SUPPLY IS DISCONNECTED AND ISOLATED

BEFORE MAKING ANY MAINS

CONNECTIONS. All mains electrical

connections must be carried out by a

qualified electrician and must comply with

the current local regulations (e.g. IEE).

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 27 28

Comentários a estes Manuais

Sem comentários