Cooper Security i-on 16 Guia do Utilizador descarregar pdf (Página 32)

i-on30EX

Page 28

Log capacity

Up to 350 events: 250

mandatory events, 100 non-

mandatory. Stored in

EEPROM memory, available

for at least 10 years without

power.

Internal Clock

±10 minutes over one year

(depending on the accuracy

of the mains supply

frequency).

User Codes

50 (plus installer code)

Remote controls

50 (one per user)

Panic Alarms

50 (one per user)

Proximity tags

50 (one per user)

Notes:

1. Wired keypads, wired zone expanders,

and radio zone expanders are all bus

devices. You can connect any

combination of these devices to the bus.

2. The system can be used as EITHER a

partitioned system OR a part setting

system. When used as a part setting

system there are four setting levels

available: Full Set and Part Sets B, C and

D.

Security

Security

Grade

Grade 2

Radio

detector

differs

16,777,214 (2

24

-2).

Radio

Supervision

Programmable.

Number of

access codes

50 plus one installer

Access code

differs

10,000 differs with 4 digit

codes.

All digits may be any

number 0 to 9.

Code blocking

Blocked for 90s after 10

incorrect codes in series.

Proximity tag

differs

4,294,967,296 (2

32

)

Power Supply

This product complies with the requirements of

EN50131-6 Type A power supply at Grade 2 and

environmental class II.

Power supply type

A

Mains power supply

requirements

230VAC +10%/-15%,

200mA max, 50Hz.

Total power supply

capacity:

1.0A

(of which 200mA is

used for battery

recharge and 800mA

is available for

powering the

system).

12V Aux supply*:

550mA max

12V Bell supply*

550mA max

Comms power

supply*:

400mA max

12V Expander

Bus*:

400mA max

LS connectors

280mA in alarm.

*Note: The ratings given here represent the

maximum current that can be drawn before

triggering over-current protection.

EN50131-6 ratings

The i-on30EX provides space for one 7Ah

battery.

For Security Grade 2 the required battery

standby time is 12 hours. This means that

all the devices powered by the backup

battery, including the control unit and at

least one keypad, should together draw no

more in total than an average of 580mA

over a 12 hour standby time.

The table below shows the current

consumption of the control unit and each

device that can be fitted to it.

CIE power

requirement:

100mA min.

120mA max

Keypad power

requirement:

30mA (backlight off)

45mA/65mA

(backlight norm/bright)

60mA in alarm

Wired Expander

requirement

20mA max quiescent.

300mA in alarm if

sounder connected.

Radio Expander

requirement

40mA max quiescent

320mA in alarm if

sounder connected.

Battery charging

requirement:

200mA (recharge

within 72 hrs)

Plug-on

Communicator

power requirement

(i-sd02 or i-dig02):

20mA quiescent

50mA max

Plug-by

Communicator pins

require:

5mA each when

active.

10 FSL zones

20mA

5 CCL zones

30mA

12V Bus output

voltage range :

10±0.5V to 13.8V

12V Aux output

voltage range:

10±0.5V to 13.8V

1 2 ... 27 28 29 30 31 32 33 34 35 36

Comentários a estes Manuais

Sem comentários